Roofing dumpster rental in Wellington
Need a roll-off onsite when your roofing crew starts the tear-off? We drop a 20-yard dumpster, then haul it away with the swap-out on the same day.
Roofing Tear-off Dumpster Sizing by Squares
How big a roll-off do you actually need for a roof tear-off in Wellington? Most homeowners use this rule: one square of asphalt shingles equals two-thirds of a cubic yard. Our 20-yard container handles a typical job; this low-wall roll-off keeps loading simple. Watch your tonnage, as shingles add up fast in Palm Beach County.
15-Yard Roofing Dumpster
- Capacity: 15 cubic yards
- Fits: 15–20 squares of asphalt shingle
- Best for: Single-layer ranch and bungalow tear-offs
Our 10-yard can fits in any tight driveway for small shingle jobs on a single haul under tonnage.
20-Yard Roofing Dumpster
- Capacity: 20 cubic yards
- Fits: 25–30 squares of asphalt shingle
- Best for: Most two-story residential tear-offs
The 20-Yard Container works well for roof tear-offs because low side walls let crews ground-throw shingles with less scaffolding.
30-Yard Roofing Dumpster
- Capacity: 30 cubic yards
- Fits: 35–45 squares of asphalt shingle
- Best for: Multi-layer tear-offs and small commercial roofs
Use the 30-Yard Roll-Off Container for large roof tear-offs to avoid a second haul-out and keep projects moving.
Asphalt Shingle Weight and Tonnage Planning
The three-tab shingle averages about 250 pounds per square; architectural laminate runs closer to 400. A 25-square tear-off lands between three and five tons before underlayment, so we route a hooklift truck with roofing dumpsters to haul full loads within the weight limit on one trip. How does that translate to a 10-yard? It caps the tonnage so the container doesn’t bottom out on the drive back from the landfill.
When shingle debris gets mixed with framing or sheathing offcuts, we route that load to our general C&D debris service—not the standard roofing container. We run these materials to the proper facility to ensure your project stays compliant.
Driveway Placement for Roofing Crew Workflow
Our crew in Wellington angles the roll-off so the swing-door faces your roof eave, allowing workers to ground-throw shingles directly into the container. We place wooden planks under the rollers to protect your concrete; this ensures the driveway remains unscarred throughout the project. Before you consult our roof tear-off container sizing, review the asphalt shingle disposal best practices guide. We set a six-foot tarp perimeter for the final nail sweep.
Drop angle
Rear door toward the roof line
Set the swing-door end facing the eave where your crew is working so walk-in loading and ground-throw share one path.
Surface protection
Wooden planks under every roller
Loaded shingle weight can gouge concrete; driveway boards must stay under the rear rollers for the full rental window.
Sweep zone
Six-foot tarp perimeter
Stage magnetic sweepers and tarps on the tarp side so nail cleanup runs in parallel with loading debris.
Tile, Slate, and Metal Roof Tear-off Containers
Concrete tile, natural slate, and standing-seam metal punish a standard bin: they weigh two to four times what asphalt does per square. We route a 30-yard low-wall container with reinforced sides and a heavier floor plate to manage these loads; this ensures the axle weight remains compliant. We cap the fill volume below the visual rim and use a lowboy for transport. Reach out for our general construction debris service for your next mixed project.
Same-day Pickup for Fast Roof Project Turnover
Tear-offs run on tight crew schedules; the roll-off shouldn’t sit idle. Dispatch coordinates the same-day haul-out around the crew’s demobilization window so the container frees the driveway for inspection or gutter reinstall before the homeowner steps back in. Our Wellington crews route the swap-out fast—back on the truck before the crew leaves the site!